Видео

I bought that same AV to HDMI! (It was OK, but I ended up upgrading to an ODV GBS-C, and it was MUCH better!)

Hello ! i have a burnt transistor but cant read its reference. Its located right after the big 1 ohm resistor Or alternatively, could i get the meter as spare ?

Thanks for your video, I'll be using it once the fan motor comes in. My Roborock currently producing a high pitch noise from the fan area while vacuuming

Hei. Vurderer kjøpe dette. Fremdeles fornøyd med det? Testet med gass?

So, did you ever get it to work?

If the bottle glass & Westclox glass are roughly equivalent at blocking alpha particles, The ratio of detected alpha-radiation from the smoke-detector in the bottle vs outside bottle was .412/5.12 = 12.42 Since you only tested the Westclox Big Ben outside through the glass, its the equivalent of the 1st number, Max you measured through the Westclox clockface glass was 11.12 if the Westclox glass is blocking the same ratio of alpha-radiation as the bottle glass, factor of 12.42, if you took the Westclox Glass off the front you should get a reading close to 11.12 with glass x 12.42 glass-blocking factor = 138.19 So whats the dangerous amount of alpha radiation?

Thank you for making it so clear what to do!

Hello. Tell me, I have a Fluke 179, in diode test mode, at the output of the device 7.3 Volts. Does your device have this voltage too?

Thanks for this video! You really know your way around this robot... Can you help me solve the problem I have with the same robot? Does robot have sensors for mop washing and where are they located? My mavx is finding the dock with no problem for docking/recharging, but is unable to find it for mop washing. I know there is a wash detection switch at the rear. Do you know what's it's purpose, maybe that is a part I need to replace?

I have the same transistor tester, B&K520b is a very good transistor tester. I been using for 35 years without any problem. Best Regards

Thank you, -longwire!

Caps from the ,70ies or before?

How much psi ?

You think I can connect this between the antenna and an old Pioneer receiver?

FINALLY someone mentions how they feel when you lay on a pillow! THANK YOU!!!

Telenor boards from 70 ies

Wire is resistant wire, constantan

Make your own scale.

All meters can be adapted to what you want.

Krafttransistorer, store variable kondensatorer fleire i paralell. Monterer deler på pcb med store motstandar, dvs i praksis isolert.

For adjusting condesators, frekvens justering med utveksling.

Har lite svårt med Norska, men jag förstod nog allt ändå 😋 Superbra video! Är du nöjd med denna svets och använder du den fortfarande?

Great you did it!!

Could this work for both AM and FM receivers?

It could be air or a ghost

Great, thanks a lot, I could fix ours as well!

Liar, liar!!!

❤❤❤❤❤❤❤👍👍👍😎😎😎😎yes

Takk for instruksjon. Har nettopp kjøpt. Kva er innstillinga på den svarte skruen med tal på i trådmatinga?

nice, wonder if the Fan motor in the S8 fits and works in the S7 MaxV 😆

I just purchased this I hopes ok

i had a problem with the lights at both sides of headset, anybody can help me with that?

My jbl tune flex earphone case’s lights are continuously and always on and blinking (just like it’s charging).can I know why is that?anyone have solution for it.its very annoyed.

Hi brother. Can you give me the Website please

Does anyone replace the S7 fan with S8 ultra fan ( 9.01.1867 ) ??? Any chance to be compatible ???

I've been wanting to get me a scope. Seems like every time I get the expendable money , something comes up

Books should do like DeWalt does in Charlotte North carolina. When they take a tool in, no matter who the manufacturer, the repairs never going to cost you more than half the price of a new replacement which seems fair to me. Now if they took that meter and put a new board in it etcetera send it back to you for $300 hey I'd be okay with that

I've been looking at a couple videos because I have a 177 that reads 4.7k ohms. I share your opinion on loyalty with fluke. As you stated they won't sell parts, so that leaves dealing with sketchy third party sellers. At this point you might as well try a cheap part or maybe even be able to incorporate some of the contact pieces from the ordered one into the existing. I sure like to figure out what's going on with mine. I at least have insight as to how much it's going to cost me LOL 300 bucks at least

Thank you!!!

Jo, which electrical part is on CF2, right from the condensator of the vakuum-engine?

Hi, good job! I have a q7 and the side brush stoped spinning, I've replaced the brush and the motor but it still doesn't spin. Any ideas? I've tested the motor and it does work.

"Assembled in USA."

@LUNORTEK what type of screw driver did you use?

Hello, my Roborock S7 Max Ultra drew water into the robot. My child started the water pump in the bottle and the robot sucked the water flowing onto the ground. After that it started giving internal error and fan error. what should I do. Is there any chance of saving the robot?

Hi, watermark - you mean marker would change color once wet? I assume warranty void if that happens?

The pump I am trying to fix has no heat and no error codes. All sensors and flow switch are good and so are the elements. The customer changed the heating unit. Is wiring the elements in the incorrect sequence going to cause a problem? With the unit facing me the top nearest ptc is wired to the left terminals on the board is this correct?

You're lucky they did the 18650 mod my razer nari ultimate lasted about 2 hours on the built in battery before i did the 18650 mod

💘 'promosm'

Kult, hva program designer du i og er filen til denne holderen din tilgjengelig? Har bestillt samme 3d printer som deg, venter på på pakken :) Mvh Rune